A ring magnet drawing needs three basic dimensions: inner diameter, outer diameter, and axial thickness. It also needs a view that shows the magnetization and pole locations. Two rings with the same dimensions can behave differently if their pole layouts differ.
Define the bore, outer diameter, and thickness
Inner diameter (ID) describes the bore. Outer diameter (OD) sets the outside envelope. Axial thickness is the distance between the two end faces. Identify the surface that locates the ring in the assembly. A shaft that passes through the bore may need clearance, while a shoulder may set the final axial position. Set the limits using the mating part drawing.
Choose a locating feature before setting limits
A shaft through a ring does not always locate it. In some designs the housing locates the outer diameter and the shaft passes freely through the bore. In others the bore locates the ring and the outer diameter must clear a housing.
Draw the section in its assembled state and label the locating surface. Then decide which diameter controls position, which one provides clearance, and which face sets the axial stop. If the ring can shift within its seat, check how far it can move before it reaches a neighboring part or changes the working gap.
Show where the poles belong
For a simple axially magnetized ring, the opposite poles are on the flat end faces. With a simple radially magnetized ring, the opposite poles are on the inner and outer cylindrical surfaces. If the design calls for several poles, add a pole map with a starting reference and a named viewing side. Ask the supplier to review the required pattern for the stated geometry.
Check the clearance implied by the limits
For a simple coaxial ring and shaft, subtract the largest permitted shaft diameter from the smallest permitted finished bore. The result is the minimum diametral clearance for the idealized pair. For example, a 10.10 mm minimum bore and a 10.00 mm maximum shaft leave 0.10 mm of diametral clearance. These are example inputs for the calculation.
If the two axes can shift, or if the bore and shaft shape matters, check the effect separately. Use finished dimensions when the coating is part of the fit. Confirm once whether the clearance requirement is stated across the diameter or per side.
Call out grooves, chamfers, and measurement points
If a chamfer guides insertion, show which edge needs it. If a groove takes a retaining part, show its location and section. Where a finish is specified, state whether key fit limits apply to the finished part. A section view helps distinguish a usable straight bore from its lead-in.
Give polarity and pole count their own drawing callouts
A short note such as “axial” identifies a direction, but the assembler may also need to know which end face must be north. Point to the named face and show the intended installed orientation. For a multipole ring, indicate the pole count, angular sequence, and where the first pole falls relative to a locating feature, when those details matter.
State whether the observer is looking from the top or bottom face. If a supplier proposes a different pole pattern or manufacturing route, ask what drawing callouts would change and whether you can compare samples in the same application setup.
What if you only have a sample?
Add a photo showing how the ring is installed and identify the side that faces the mating part. If you have measured the bore and outer diameter, label those values as sample measurements. Ask what still needs confirmation before those dimensions or the pole layout become order requirements. For rings located by the outer wall, show the housing seat and check how much bore clearance remains at the installed position. If the ring is located by the bore, check the outer wall against the housing envelope in that condition.
Pick inspection points that match the function
Distinguish the straight bore from the lead-in chamfer when a shaft must pass through. If the axial thickness controls a stack, show which bands on the end faces contact adjacent parts. If the magnet is checked with a sensor, describe the probe location and its distance to the ring.
Consider whether the ring is measured on its own or in its holder, especially if the holder or mating part affects the result. Write the inspection condition on the same drawing revision you send for a quote so the supplier can flag a measurement it needs to discuss.
Prepare the ring magnet inquiry
For a ring that seats on a shoulder, include one section through the shoulder and a separate view that identifies north and south. Mark the surface that establishes the height and the bore area that the shaft must clear. If the same drawing covers two polarities, distinguish the part numbers or variants, and ask the supplier to show how the parts will be identified at delivery and during incoming inspection.
Use Ferrite Ring Magnets and NdFeB Ring Magnets to identify candidate product categories. Send a marked drawing, pole map, working conditions, order quantity, and any known material or functional target via Contact Us. Include a sample only with a note explaining what the supplier should match.

