Start an arc magnet drawing with the actual rotor or stator interface. Identify the surface the magnet seats against and the axis or center used to define its arcs. Then specify the radii, angle, and axial length. The installed geometry sets the context for both clearance and inspection.
Identify the mounting side
Show the magnet in an assembly section and mark the surface that seats on the rotor or stator. Name the air gap side separately. If the magnet has an axial stop or a key for angular location, show how those features line up with the mating part.
Build the drawing around the installed axis
Show a section across the rotor or stator that includes the magnet, the part it seats against, and the air gap. Label which features establish the installed axis or center. If a rotor pocket locates a segment on flats or sidewalls, show those contacts as well as the curved face.
A radius dimension alone cannot show how the pocket prevents sideways movement. When the magnet detail drawing uses a local reference, add an assembly view that relates it to the motor axis. A reviewer should be able to place the part in the correct orientation from the drawing package.
Dimension the arc from a named reference
Give the inner and outer radii and show the center used for each. If both arcs share a center, radial thickness is the difference between their radii. For offset centers, define the thickness at the required location or control the profile. A chord spans the arc endpoints in a straight line. If you use a chord, state which arc it belongs to. Show axial length in a separate view.
Specify one coherent set of arc dimensions
Use a section normal to the motor axis to show the arc. For a concentric segment, an inner radius, outer radius, and included angle can define the main outline when the two end faces follow the stated radial boundaries. Add end cuts or flats if the ends differ from that geometry.
If your inspection uses a chord instead of the angle, mark the correct endpoints. For a circular arc, the outer arc and inner arc have different chord lengths at the same angle. Confirm which dimensions control acceptance and label any extra values given only for reference.
Separate pole information and mechanical clearance
Add the required pole direction and label the viewing side. For a segmented layout, identify the position of each segment in the assembly. State the required clearance and how the magnet is retained. For a bonded design, confirm whether the installed position accounts for the bond line. Check clearance using the installed parts and their tolerances.
Review the running clearance in the assembly
The running gap depends on the parts around the magnet and on how the magnet is located after assembly. Show the gap you intend to maintain and the surfaces from which it is measured. If there is adhesive, a sleeve, or a retaining feature on the gap side, include its installed position in the section.
Identify cases where dimensions or alignment could lead to a local minimum gap. If the drawing is intended for quotation, state which clearance limits are already approved and which still need design review. Confirm the final gap on the assembly at the relevant inspection stage.
How do you cross-check an arc drawing?
Overlay the segment section on the mating part using their shared reference. Check whether the dimensioned seating face matches the intended side and whether the segment ends clear nearby parts. If a drawing calls out both chord and angle, confirm that the dimensions agree for the stated radius. If an edge break affects the seating length, dimension that feature on the detail view. Include the mating face in the same section so a reviewer can see which portion of the arc must actually make contact.
Connect the pole map to the build sequence
A pole map should use the same viewing side as the assembly instruction, or state how to convert between the two views. If several segments have identical geometry, identify whether they use the same magnetic orientation or different orientations. Document how the installer distinguishes them at the station.
If polarity is checked after placement, name a face or position that can be reached in the installed state. Send the pole arrangement as a separate controlled sheet if different teams own the magnetic and mechanical drawings. Include both revisions on the assembly drawing so a quote refers to the intended combination.
Send an arc magnet drawing for review
Before releasing the package, check that the segment detail, mounting section, and pole map use compatible names for the same feature. For example, use the same term for the seating arc in the drawing and the inspection notes. Flag a remaining choice such as the method of retention and ask whether it changes the dimensions required for a quote. Supply a revised drawing if the choice changes the installed position.
Review Ferrite Segment Magnets or NdFeB Segment Magnets as a starting point. Send the current segment drawing, rotor or stator section, pole map, quantity, and proposed inspection reference via Contact Us. Flag any dimensions that still depend on an open motor design decision.

