Choose a magnet coating based on what the magnet will contact and how you will install it. For sintered neodymium iron boron (NdFeB), include both corrosion exposure and the condition of the coating after assembly. If you have yet to select a coating, describe the protection you need and ask which options can be verified.
Describe real exposure
List service and storage temperatures, humidity or condensation, and any water, salts, cleaners, or other fluids that may contact the magnet. Say whether contact is occasional, repeated, or continuous. A part inside a housing may still see condensation or cleaning fluid through openings.
Describe exposure as a sequence
Write down what happens from storage to installation and use. A magnet may be stored in a dry area, assembled during a wet cleaning process, and then see repeated condensation during operation. Record which surfaces are exposed during each step and whether liquid can collect at a joint.
If cleaning is part of the process, provide the agent and contact conditions available from the process owner. Include any expected drying period when it affects exposure. A supplier can use this description to identify which coating questions can be answered from a specification and which need testing on a representative part.
Check what happens during assembly
Identify any surfaces that slide across an edge, contact a tool, or receive adhesive. For a bonded part, share the planned surface preparation and adhesive system. For a tight fit, specify whether the limit applies after coating. Evaluate the finish on representative parts if the insertion step may damage it.
Identify vulnerable surfaces and verify finished fit
Use a section or marked photo to show the edges, recesses, and contact areas that matter. Identify the surfaces that carry adhesive and the surfaces that rub against a housing during installation. For a coated ring that fits a shaft, specify whether the bore limit applies to the finished part and where to check it. For a magnet bonded into a shallow pocket, include the coated thickness and bond line when reviewing available height.
If the design permits a different edge detail, mark it for review. Edge geometry can affect both chip risk during handling and how a coating covers a corner. See Arnold Magnetic Technologies: Magnet Manufacturing Process.
Define the inspection criteria
Identify the covered surfaces and any appearance, thickness, or adhesion criteria that matter. If you require salt spray testing, cite the agreed edition and specify exposure duration, sample state, and the pass criteria. ASTM B117 describes the test environment. Its results alone seldom predict service performance. See ASTM B117 scope.
Select a test that answers the intended question
A test for coating appearance at receipt answers a different question from a test for damage after insertion. For corrosion evaluation, agree on the part or coupon to expose, which areas are evaluated, and how a failure will be recorded. If the buyer expects a salt spray report, list the specimen state, the cited edition of the practice, exposure duration, and what the inspector will count as a fail.
Also ask whether test data came from the quoted part geometry and coating system. If the setup differs from service, use the result within that setup and define what application checks are still needed.
What if the same finish is used on two shapes?
Check the new part where it is hardest to protect or inspect. A recessed area, a sharp edge, or an insertion face may need a separate check. If the service risk comes from installation, agree whether evaluation should include parts taken through the actual assembly process. State which party will judge the samples and when the inspection takes place. A check immediately after coating answers a different question from a check after parts go through handling, transport, and installation. Use the stage that matches the risk you need to assess.
Make the finish options comparable in the quote
If you accept alternate finishes, put the same service conditions and finished dimensions on each option. Ask which surfaces receive the finish and whether thickness or visual checks are part of the quote. For an adhesive joint, state whether the application team will check the bond with the proposed finish.
If the supplier can only share data for a related coating, identify what differs and plan a sample check. Record the chosen finish, drawing revision, and agreed inspection condition once the sample is reviewed. Production and incoming inspection can then use the same definition of the accepted finish.
Request options for the specific NdFeB part
A coating request can be as specific as a drawing, a list of exposed surfaces, and a description of the assembly trial. For example, ask for a candidate finish for a magnet that is bonded into a housing and exposed to condensation, together with the finish limits that apply to the quoted part. State whether you plan to evaluate corrosion on loose magnets, completed assemblies, or both. Have the supplier identify any assumptions about sample preparation.
Review the Neodymium Magnets category, then send the drawing, exposure summary, and assembly method via Contact Us. Ask which coating systems are available on that part and which inspection records or representative samples can support your review.

